Making a hole on the bottom of a horizontal pipe will cause any sediment in the pipe to collect in the valve and can cause a blockage, so I made sure to drill into the top of the pipe. This line could be one from the basement, the kitchen sink, or elsewhere. The icemaker kit includes a valve and a clamp. If you have a choice, select a vertical pipe not horizontal, as sediment can enter the fridge water line easier 2 Types of Water Valves can be used Saddle Valve or In Wall Water Valve for Refrigerator Water Line Step 2 — You will be drilling a hole into the cold water pipe so turn off the main water supply to your complete house. For me it was faster than the the saddle and it gave me a chance to replace my 30 year old corroded stop. With no basement water pipe to attach it to.
The water line kits are fairly inexpensive and will come with a new valve that can be installed on the cold water pipe. Flare connections are much more leak resistant than the commonly used compression type fitting that contains the small brass o-ring. Thanks for contributing an answer to Home Improvement Stack Exchange! If you are trying within the service hours and still getting this message, please try again after some time. Step 1 — Turn off the Water Shut off the water valves to the faucets. If your refrigerator is across the room from your kitchen sink, there may be a closer water supply line in an adjacent bathroom or garage.
More information may be included on the instructions that are included in the icemaker kit, so make sure to thoroughly read those first! Or, message all the mods and we will push your post thru. The valve may also be stuck open and water flows constantly. It's a good idea to have a pair of needle nose pliers handy to grab the wiring harness behind the large hole in the back of the freezer. Put the end of the water line into the empty bucket. Step 3: Shut off the water supply to the refrigerator — Usually there will be a water supply valve in the wall behind the fridge.
A quick fix is to install the newer style of flexible lines, available at almost any hardware store. The cold tap water and the room temperature water froze at virtually the same time. What is the best way to protect the floor beneath the refrigerator in case a leak happens? Refrigerator Water Supply Most modern refrigerators include filtered water and an ice dispenser. Self-Tapping Saddle Valves Just like the name implies, these valves look like a saddle seated on top of a pipe. One hose easily connects in seconds.
Because of this, they should always be installed in visible, accessible locations; never hidden inside walls, ceilings, or floors. Remember — after the nut is hand-tight, use the wrench or pliers to turn the nut a half turn! This can cause a leak. Access for this is no issue and it's a fairly close ~15 foot shot to my fridge. The ice makers typically require a small soft copper water supply tube whose outer diameter is only one quarter inch. Next, back the pin all the way out. If the tubing is plastic, insert the brass bushing provided with the saddle valve into the end of the tubing; this reinforces the tubing for a tight connection it is not needed for copper tubing. To learn more, see our.
Use a strip of emery cloth to buff-clean a section of the copper water line. Turn the main water on to your home. Insert the tubing all the way into the compression fitting. Be sure to put a drip pan under the valves. Refrigerator water inlet valve has wire harnesses connected — Disc onnect the wire harnesses Step 7: Install the brand new water valve assembly — Attach it onto the same mounting bracket where the old one was located — Secure it in place with the screws or bolts that came with the new valve. I told him to grab a saddle valve and turn his weekend project into an hour-long project.
Leave the tubing to fall freely to the floor when it reaches the location of the refrigerator. Tape the end of the tubing and push enough tubing through the hole to make a couple of large loops. If possible, drill the hole from the top down to ensure correct placement. Tighten up the mounting screws to secure the unit to the freezer wall, and then add the ice bucket under the kit. Your fridge should now have a perfectly working ice maker and water dispenser! If your fridge has a door water dispenser,.
Repeat this process to connect the red-tipped black water tube and the red fitting. Indeed virtually all modern plumbing materials are manufactured out of some form of plastic or other. But I have always doubted it to be true. If you have a water dispenser on your fridge, dispense about a gallon of water and spill it down the kitchen sink drain. Be sure to put a gasket seal between the valve and the T-fitting. Even if hot water was better, just as it got to the refrigerator the automatic ice maker valve would stop the water flow.